Evident LogoWabtec Logo

Thickness and Flaw Inspection Solutions
Specifications

GENERAL

Housing Dimensions 230.7 mm × 166.9 mm × 71.9 mm (9.1 in. × 6.6 in. × 2.8 in.)
Weight 1.8 kg (3.98 lb), including lithium-ion battery
Battery Life Over 8 hours for standard operation
Operating Temperature -10 °C to 50 °C (14 °F to 122 °F) operating temperature range at 80% relative humidity
Storage Temperature -20 °C to 50 °C (-4 °F to 122 °F) [with batteries]
Display Type 7-inch TFT LCD (thin-film-transistor liquid crystal display)
Display Dimensions (WxH, Diagonal) 154.2 mm × 85.9 mm, 177.8 mm (6.1 in. × 3.4 in., 7.0 in.)
Power (DC-IN Voltage) 24 VDC (60 W)
DC Connector Circular, 2.5mm pin adapter, center-positive
Data Storage 64 GB internal storage

PULSER

Pulse Voltage 100 V, 200 V, 300 V, 400 V, unipolar excitation
Pulse Damping 50 Ω or 400 Ω
Pulse Repetition Frequency 10 Hz to 2000Hz, “Single Shot” (always equivalent to measurement rate)
Tunable Square Wave Pulser 20 nanoseconds to 5000 nanoseconds (100kHz to 25MHz), user adjustable
Pulse Modes Pulse-Echo, Dual, Thru Transmission (TTU)

RECEIVER

Gain 0 to 110 dB, 0.1 dB increments
Filters 23 digital filters*, Narrowband, Wideband, and Low-Pass
Rectification Fullwave, Half+, Half-, RF (Unrectified)
A-Scan Bit Depth 24 bits
Stored A-Scan Samples Minimum 1024 saved A-scan points @ 24bit/point
Amplitude Range User selectable 0-110%, 0-400%, or 0-800% full screen height
System linearity Horizontal: ± 0.5% FSW
Resolution 0.25% FSH, amplifier accuracy ± 1dB
Reject 0 to 85% FSH in 1% increment positions
Measurement rate Equivalent to PRF in all modes (single shot)
Sample Rate User selectable standard (200 MS/s), extended range (25 MS/s), or high resolution (400 MS/s)

CALIBRATION

Automated calibration Velocity, zero offset
Straight Beam (First Backwall or Echo-to-Echo)
Angle Beam (Soundpath or Depth)
Test modes Pulse Echo, Dual, or Through Transmision
Units Millimeters, inches, or microseconds
Range 3.5 mm to 24,500 mm at 5,900 m/s (0.138 in. to 1,000 in. at 0.2320 in./µs)
Velocity 635 m/s to 15240 m/s (0.0250 in./µs to 0.6000 in./µs)
Zero offset 0 to 750 µs
Display delay 0 microseconds to 2,203 microseconds
Refracted angle 0° to 85° in 0.1° increments, then jump to 90°

GATES

Measurement gates 2 fully independent flaw gates, 1 interface gate
Gate start Variable over entire displayed range
Gate width Variable from 0.040 microseconds to end of displayed range
Gate threshold Variable from 2 to 100% full screen height in 1% increments
Alarms Positive and Negative Threshold
Gate sychronization Gate synchronization in Gate B-A, Gate A-1, Gate B-I

MEASUREMENTS

Measurement display locations 5 locations available (manual or auto selection)
Gate (A, B) Thickness, Soundpath, Projection, Depth, Amplitude, Time-Of-Flight
Echo-to-Echo Standard Gate B - Gate A
Other measurements Overshoot (dB) value for DGS/AVG, ERS (equivalent reflector size) for DGS/AVG, AWS D1.1/D1.5 A, B, C, D values
Sizing Methods DAC/TCG, TCG Table, AWS D1.1/D1.5, DGS/AVG

ENVIRONMENTAL

IP Rating Rated IP65
Drop-Tested Method 516.6 Procedure IV, 26 drops, package for shipment
Shock-Tested MIL-STD-810H, Method 516.5 Procedure I, 6 cycles each axis, 15G, 11 ms half sine 6 cycles each axis, 15G, 11 ms half sine shock testing
Vibration-Tested MIL-STD-810H, Method 514.5 Procedure I, Annex C, Figure 6, general exposure; 1 hour each axis vibration test

INPUT / OUTPUT

Connectivity • USB C peripheral port (supports USB 2.0, USB 3.0, display port over USB alternate mode, Ethernet over USB 2.0 with optional external adapter)
• Wi-Fi/Bluetooth
• 19-pin LEMO I/O connector
Alarm Output 3 Digital Alarm Outputs, 5V TTL
Analog Output 2 Analog Outputs, 0-1V or 0-10V scaling
Encoders 2 axis quadrature encoder inputs
Synchronization (Trigger Sync) Sync Input & Output Signals
Sorry, this page is not available in your country

Let us know what you're looking for by filling out the form below.

Sorry, this page is not available in your country